Factory reset (Yealink) in the Zoom app

Resetting your Yealink phone and installing custom firmware is as easy as following this article.

Note: For a detailed explanation of the deployment process, see the Deployment Quick Start Guide.

This article covers:

• How to get the IP address of the phone
  • T4 series without touchscreen
  • T4 series with touchscreen
  • T5 series with touch screen
• How to access the phone’s web interface
• Factory data reset via web interface (recommended)
• Factory data reset via phone UI (optional)
  • T4 series without touchscreen
  • T4 series with touch screen
  • T5 series with touch screen
• How to install custom firmware via web interface

Requirements for factory reset and installing custom firmware on Yealink phone

• Firmware file for the custom device (accessible from the Zoom web portal or from the certified devices list).
• Zoom Phone supports Yealink devices
• The web interface for desk phones is enabled in the account-level settings

How to get the IP address of the phone

T4 series without touchscreen

1. Pressing the menu button takes you to the menu.
2. Use the phone’s directional keys to select Status.
3. The IPv4 address should also be noted.

T4 series with touch screen

1. Select Menu from the home screen by tapping it.
2. Choose Status from the menu.
3. The IPv4 address should be noted.

T5 series with touch screen

1. The home screen can be accessed by swiping left.
2. Choose Settings from the menu.
3. Select General.
4. The IPv4 address should be noted.

How to access the phone’s web interface

Note: Check the account-level desk phone settings to ensure the web interface is enabled if you cannot access the phone’s web interface.

1. Connect the phone to the same network as a computer running a web browser.
2. In the previous section, you entered the IP address of the phone.
3. An administrator can access the phone’s web interface.
   Note:
4. By default, admin and admin are the username and password. The phone seller can give you the username and password if you don’t know them. On the Zoom web portal you can view the admin password if it has been set globally.

Factory data reset via web interface (recommended)

Note:

On older Yealink devices, the navigation menu is on the left side instead of the green header bar.

1. In the left navigation menu, click Settings and then click Upgrade.
2. Select Factory data reset.
3. Confirm with OK.

Factory data reset via phone UI (optional)

You can access your phone’s web interface by following the steps in this section.

T4 series without touchscreen

1. The menu button should be pressed.
2. Use the directional pad to access advanced settings.
   Note:
3. Admin password is required (admin by default). Contact the phone provider if you do not know the administrator password.
4. On the phone’s directional pad, select Config. reset > reset to factory settings.

T4 series with touch screen

1. Go to the home screen and tap Menu.
2. Select Advanced.
   Note:
3. The password for the administrator will be requested (by default it is admin). The phone provider can tell you the admin password if you don’t know it.
4. To perform a factory reset, tap Reset config.

T5 series with touch screen

1. The home screen can be accessed by swiping left.
2. Select the Settings option from the menu.
3. To access the Advanced Settings section, scroll to the bottom of the page.
   Note:
4. The advanced settings can only be accessed if you enter the admin password (the default password is admin). It is advisable that you contact the seller of the phone if you cannot remember the admin password.
5. Reset the configuration by tapping the Reset Config button.
6. From the Factory data reset menu, tap the Factory data reset button.

How to install custom firmware via web interface

note:

On older Yealink devices, the navigation menu is on the left side instead of the green header bar.

1. Navigate to Settings and then Upgrade on the left side of the screen.
2. Double click to select the custom firmware file after clicking browse or choose file.
   Note:
3. The custom firmware version can be downloaded or checked from the supported devices list.
4. Start the firmware upgrade by clicking Upload. After the custom firmware is installed, the phone will reboot. It takes about two to three minutes for the process to complete.

---

Read it too –

---

frequently asked Questions

How do I factory reset my zoom?

It is possible to reset the device to factory settings via the web interface (recommended).

1. To backup and restore your phone, click on the Utilities tab in the top navigation menu.

2. Using the link below will expand the Global Settings section if that’s what you want.

3. Recover the data by clicking on the Recover button.

4. You must click Yes to confirm your action.

how do i reset mine Cell phone with zoom?

The phone should be off. If you hold down the volume down button at the same time as you hold down the power button, you can turn on the phone as long as you keep both buttons pressed at the same time. You will see the recovery mode on the screen as soon as you press the volume down button.
Resetting the device can be achieved by following these steps:

1. To access the system settings, go to the Settings menu.

2. Then touch the Advanced button.

3. When there are multiple options You touch the reset button.

4. You can erase all your data with the push of a button (factory reset).

How do I reset the default zoom in Chrome?

All web pages can be set to the same font or page size

1. The first thing you need to do is open Chrome on your computer.

2. Click the More button at the top right of the page. Ideas.

3. Choose Appearance from the menu.

4. You can make the changes you want by clicking the down arrow next to Page Zoom and then selecting the zoom option you want Demand. . Once After you do this, you will be prompted to choose the zoom option you want to use for your document. You need to click the down arrow next to “Font Size”. to change the font size so you can change the font size.”

How do I sync my zoom accounts?

Access Zoom’s web portal by logging in with your Zoom account. You can access your account profile by clicking Account Management in the navigation menu. In the next step, under Link accounts to an organization, click Link to existing organization. A link to an existing organization can be requested by entering the organization owner’s email address in the pop-up window that appears when you click the Link to Existing Organization button.

Does Zoom sync across devices?

The meetings you schedule should sync across all your devices, provided you’re signed in with the same account on all of them.

How do you unlock the zoom?

To access User Management, click the User Management button in the navigation pane. It is possible to unblock a user’s account by clicking the Unblock button next to their email address. After unlocking their account, you can now change their password for them, or they can reset their password for themselves by going to the Zoom Forgot Password page after unlocking their account. book page.

---

Related Articles